Chapter 03 · 11 min

Race day: heats, results, corrections

The admin workspace step by step: working the bracket, tapping placements, recording times, firing the start signal, and fixing mistakes.

01

The phases of a race

A race runs through five phases. What you can do depends on where you are.

PhaseWhat happensWhat you can do
SetupRace created, roster buildsMetadata, roster, open and close signup
Heat assignmentSeeding is calculatedRearranging, shuffle, waiting for confirmation
RunningHeats are flownEnter results, record times, correct
FinalGrand final is generatedEnter the last result
CompletedPodium is setExport, archive, create a new race
02

Working the bracket

The bracket is the control room of the race day. It shows every heat, its color, and its status.

ColorMeaning
CyanQualifying heats
GreenWinner bracket
RedLoser bracket
GoldGrand final
  • Active: animated border, ready for input.
  • Pending: waits for the previous heat.
  • Completed: click to view the results.
  • Preview: gray placeholders for heats that only exist later.
Scroll
Zoom in the bracket
Drag
Pan the bracket
Ctrl/Cmd+double-click
Reset zoom
Z
Fit to view: the whole overview, press again to jump back
P
Show and hide pilot paths
Escape
Close the modal

Pilot paths show each starter's route through the tournament. Hover a pilot to highlight their path; eliminated pilots end with an X.

03

Entering placements

  1. 1Click the active heat in the bracket.
  2. 2Tap the pilots in the order they crossed the line: first tap is place 1, second is place 2, and so on.
  3. 3Optional: record lap times if the heat was flown with timekeeping.
  4. 4Confirm with Done. The next heat becomes active automatically.
  • Partial rankings are allowed: at least two distinct pilots with consecutive places starting at 1.
  • The app rejects duplicate placements.
  • The server fills missing places deterministically in heat order.
  • In the finish dialog you see each pilot's total time, the individual laps, and the holeshot.

Typing times

After placing, three to five digits are enough. The format always starts with minutes.

InputResultExample
3 digitsM:SS123 becomes 1:23
4 digitsM:SS.z1234 becomes 1:23.4
5 digitsM:SS.zh12345 becomes 1:23.45
Range0:05 to 9:59.99shorter times are rejected
04

Start signal and holeshot

Before a heat, race control fires the start signal: a full screen countdown with sound and a voice announcement, played locally on the admin's device.

  • The countdown is not sent to other devices, only the moment of the final tone.
  • Escape or Cancel stops the countdown immediately.
  • The sound toggle only applies from the next start signal.
  • The final tone starts the holeshot: the time from the tone to the first start gate pass, 15 seconds at most.

The holeshot counts toward the total time, not the first lap. Without a start signal, the spotter timer measures the bare laps only.

05

Correcting results

Mis-taps happen. While the race is running, results can be corrected or reset, in the race management and, as an admin, also through the heat dialog of the spectator view.

  1. 1Open the affected heat in the detail view.
  2. 2Choose Correct result or Reset.
  3. 3Give a reason. It lands in the audit entry.
  4. 4Confirm the dialog. If the heat is not the last one, it lists every heat that will have to be re-flown.
  • A reset discards every later heat on that path, including their spotter assignments.
  • Pilot withdrawals are kept.
  • Ready reports and lap times of the running heat are mentioned explicitly in the dialog.
  • After the race is completed, every correction is locked.
06

Spectators and announcements

Every published race has a read-only live view. It updates over a live connection, with polling as a fallback.

  • Projector or screen: the same view works for an audience.
  • The speaker at the top right toggles spotter announcements, placement announcements, and next heat. The choice is stored per device.
  • If the connection drops, an offline notice appears with the last known state.
  • Private races have no public live view.
07

When something sticks

SymptomCauseFix
Message about an outdated viewSomeone changed things in parallelReload the page and repeat the input
Result is not acceptedToo few or duplicate placesAssign at least two distinct places starting at 1
Bracket stays emptyTournament not started or field too smallConfirm the seeding, check for 8 to 60 pilots
Pilot cannot be addedProfile missing, disabled, field full, or roster lockedCheck the index, check the phase
An earlier correction is not possibleNo valid starting stateReset the heat from the detail view with the confirmation dialog

Still have a question?

Write to FPVOOE — or take a look at the other chapters.

Contact